| 004-16836-00 |
Silver Oxide Reference Material |
Reference materials for Temperature-Programmed Reduction (TPR) Analysis |
| 004-25549-00 |
1/8in x 1/4in Tube OD Brass Reducer |
Reducer fittings for regulators |
| 004-25938-00 |
1/16in PEEK Ferrule |
For mounting the sample thermocouple in the same 1/8-in. fitting as the quartz thermocouple sheath |
| 004-25940-00 |
1/8in PEEK Ferrule |
For the quartz thermocouple sheath,which mounts through a 1/8th inch fitting |
| 004-32164-01 |
4in x 6in Bag of Quartz Wool |
|
| 004-32187-00 |
Cotton Flannel Gloves for Handling Hot Components |
|
| 004-33601-00 |
Expansion Kit that adds an additional outlet to the gas regulator with a maximum of 1000 psig |
Kit Includes: Fittings and Instructions |
| 004-33601-01 |
Expansion Kit that adds three additional outlets to the gas regulator with a maximum of 1000 psig |
Kit Includes: Fittings and Instructions |
| 004-33601-02 |
Expansion Kit that adds three additional outlets to the gas regulator with a maximum of 3500 psig |
Kit Includes: Fittings and Instructions |
| 004-54609-00 |
Wide Bristled Brush |
For cleaning sample tubes |
| 004-54805-00 |
Extraction Tool |
Facilitate the extraction of quartz wool from reactor |
| 004-61064-00 |
600ml Dewar |
Used for the cold trap slurry. Dewar can also hold liquid nitrogen for BET analysis |
| 004-61602-00 |
1ml Calibration Syringe |
For manual gas injections up to 1ml. Used when calibrating the loop volume or for manual calibration of reactive gases |
| 004-61602-01 |
3 Replacement Injection Needles for 1ml Calibration Syringe |
Includes 3 spare needles |
| 004-61604-00 |
10ml Calibration Syringe |
For manual gas injections up to 10ml. Used when calibrating the loop volume or for manual calibration of reactive gases |
| 004-61604-01 |
3 Replacement Injection Needles for 10ml Calibration Syringe |
Includes 3 spare needles |
| 004-62150-326 |
1500 psig Gas Regulator with CGA 326 Fitting for N2O |
|
| 004-62150-350 |
1500 psig Gas Regulator with CGA 350 fitting for CO or H2 |
|
| 004-62150-540 |
1500 psig Gas Regulator with CGA 540 fitting for O2 |
|
| 004-62150-580 |
1500 psig Gas regulator with CGA 580 fitting for Ar, He, or N2 |
|
| 004-62150-590 |
1500 psig Gas Regulator with CGA 590 fitting for 10% O2 in He |
|
| 004-62200-58 |
100 psig Gas Regulator with CGA 580 fitting for N2, He, Ar, and Kr |
|
| 004-62230-32 |
30 psig Gas Regulator with CGA 320 fitting for CO2 |
|
| 004-62230-35 |
30 psig Gas Regulator with CGA 350 fitting for CO, H2 |
|
| 004-62230-54 |
30 psig Gas regulator with CGA 540 fitting for O2 |
|
| 004-62230-58 |
30 psig Gas Regulator with CGA 580 fitting for N2, He, Ar, and Kr |
|
| 004-62230-59 |
30 psig Gas Regulator with CGA 590 fitting for Ultrapure Air |
|
| 008-42001-00 |
Analytical Methods in Fine Particle Technology |
A comprehensive resource of information on particle analysis. This hardbound text describes theory, instrumentation, and applications pertaining to chemisorption and temperature-programmed reactions, as well as other analytical methods used in the characterization of catalysts and other materials. |
| 021-00000-00 |
Model 021 Liquid Nitrogen Transfer System |
For a safer and easy transfer of liquid nitrogen into smaller sample dewars. Includes 47-L Dewar, dolly, and pump with a 100-cm discharge line. Universal electrical input. |
| 029-00000-00 |
CryoCooler II |
Provides seamless temperature control for fully automated temperature programmed reduction, desorption and reaction analysis. Allows furnace system to hold sample at approximately -120 °C. |
| 201-25818-00 |
6ft Stainless Steel Gas Inlet Line Assembly |
Includes stainless steel tubing, with ferrules and nuts (1/8-in. male fitting to connect to analyzer on one end, 1/8-in. female fitting to connect to regulator on opposite end) |
| 201-25818-01 |
16ft Stainless Steel Gas Inlet Line Assembly |
Includes stainless steel tubing, with ferrules and nuts (1/8-in. male fitting to connect to analyzer on one end, 1/8-in. female fitting to connect to regulator on opposite end) |
| 280-32800-00 |
Foam Support for Weighing Sample Tube |
|
| 290-25842-00 |
Gas Sampling Assembly |
Sampling compatible with calibration syringes |
| 290-25846-00 |
6ft Copper Gas Inlet Line Assembly |
Includes copper tubing, with ferrules and nuts (1/8-in. male fitting to connect to analyzer on one end, 1/8-in. female fitting to connect to regulator on opposite end) |
| 290-25846-01 |
16ft Copper Gas Inlet Line Assembly |
Includes copper tubing, with ferrules and nuts (1/8-in. male fitting to connect to analyzer on one end, 1/8-in. female fitting to connect to regulator on opposite end) |
| 290-62600-00 |
0.5ml Injection Loop |
|
| 290-62601-00 |
1ml Injection Loop |
|
| 290-62602-00 |
5ml Injection Loop |
|
| 291-31801-00 |
Half Cover for 600ml Cold Trap Dewar |
Two needed per 600ml dewar |
| 291-34005-00 |
KwikCool |
Provides rapid cooling of the furnace and decreases analysis time and increasing throughput. Works with compress air at room temperature |
| 291-53904-00 |
Sample Thermocouple |
Shaped to enter the reactor measureing the sample temperature during the experiment |
| 292-32801-00 |
Protective Shelf Mat |
|
| 292-33015-01 |
Cirrus 2 200 AMU Mass Spectrometer |
Stand alone unit |
| 292-46101-00 |
Cirrus Installation and Training for U.S.A. or Canada |
|
| 292-46102-00 |
Cirrus Installation and Training for Europe |
|
| 292-46103-00 |
Cirrus Installation and Training for Asia and All Other Countries |
|
| 295-33015-00 |
Cirrus 2 200 AMU Mass Spectrometer |
200 AMU mass spectrometer connects directly to a dedicated port on the AutoChem II 2950 for detection and identification of low concentrations of condensable and/or reactive gases. |
| 295-33021-00 |
KwikCool Vortex |
Supplies chilled cool air by a Vortex technique intended for rapid cooling of the furnace. It is not a temperature control device |
| 295-33640-00 |
Cirrus 3 200 AMU Mass Spectrometer |
200 AMU mass spectrometer connects directly to a dedicated port on the AutoChem II 2950 for detection and identification of low concentrations of condensable and/or reactive gases. |
| 295-33640-CR |
Corrosion Resistence Cirrus 3 200 AMU Mass Spectrometer |
200 AMU mass spectrometer connects directly to a dedicated port on the AutoChem II 2950 for detection and identification of low concentrations of condensable and/or reactive gases. Enhanced Chemical Resistant (ECR) Unit |
| 295-42801-00 |
AutoChem 2950 Operator's Manual |
Printed manual with binder |
| 295-53801-00 |
Furnace Assembly |
|
| 930-54603-00 |
Narrow Bristled Brush |
For cleaning sample tubes |
| 295-25801-00 |
Stainless Steel Sample Tube |
|
| 004-27041-00 |
20 Micron Filter Frit for the Sample Tube |
Placed inside the o-ring at the small stem outlet of the sample tube |
| 291-25819-00 |
Large Stem Retaining Nut for Sample Tube |
|
| 004-25011-01 |
-011 Kalrez Oring for Large Stem on Stainless Steel Sample Tube |
|
| 295-25817-00 |
Ferrule Set on Large Stem of Stainless Steel Sample Tube |
Two-part Ferrule for the large stem of the sample tube |
| 291-25816-00 |
Small Stem Retaining Nut for Sample Tube |
|
| 295-25818-00 |
Ferrule Set on Small Stem of Stainless Steel Sample Tube |
Two-part Ferrule for the small stem of the sample tube |
| 004-25465-00 |
-010 Kalrez O-ring for Small Stem on Sample Tube |
|
| 291-61702-00 |
Quartz Sample Tube |
U tube reactor |
| 295-25825-01 |
Part 2 of Small Stem Quartz Sample Tube Seal |
|
| 295-25825-02 |
Part 1 of Small Stem Quartz Sample Tube Seal |
|
| 004-25474-00 |
-013 Kalrez Oring for Large Stem on Quartz Sample Tube |
|
| 295-25826-01 |
Part 1 of Large Stem Quartz Sample Tube Seal |
|
| 295-25826-02 |
Part 2 of Large Stem Quartz Sample Tube Seal |
|
| 004-32004-00 |
Stopper for quartz sample tube inlet |
Sample tube stopper to limit sample exposure to air when sample tube is outside of the instrument |
| 004-16247-00 |
Snoop |
For gas flowmeter and gas leak checking |
| 004/16825/00 |
Platinum Alumina Reference Material |
For checking pulse chemisorption |
| 004-32604-08 |
Plastic Cap for Sample Tube Outlet |
Cap for quartz sample tube to limit sample exposure to air when sample tube is outside of the instrument |
| 029/33030/00 |
CryoCooler Mounting Hose Bracket |
The bracket helps to hold the CryoCooler hose onto the furnace without straining the tube on the furnace |
| 292-34013-00 |
25.75 OHM FE-NI-AU Detector Assembly |
Complete TCD wired detector 25.75, ±0.75 Ohms @ 70 ±3 °F, with gold coated Fe-Ni filaments |
| 004/16848/00 |
Calcium Oxalate Monohydrate Reference Material |
For Check Temperature Programmed Desorption |